PRIMARY FUNCTION:
Monitor the manufacturing processes and operations and conduct inspections of a broad range of fabrications, subassemblies, assemblies, component parts, purchased material and tooling to assure compliance with customer and NG specifications and standards where procedures and techniques are normally established.
WORKING PROCEDURE:
THE FOLLOWING ARE THE USUAL MAJOR JOB DUTIES BUT THIS DESCRIPTION DOES NOT PRECLUDE THE PERFORMANCE OF OTHER DUTIES BY THE INCUMBENT, NOR THE QUESTION BEING RAISED ON THE PROPER RATE FOR THE ASSIGNMENT.
In addition to the duties of the Inspector “C”, performs the following:
1. Inspect and test components, assemblies, tooling, weldments and materials of various geometric configurations and processes as specified and randomly for compliance with established customer and NG specifications and standards where procedures and techniques are normally established. Identify and tag defective parts, material an incorrect processes with appropriate inspection documentation.
2. Setup and use measuring equipment including surface plates, optical tooling and coordinate measuring machines where procedures and techniques are normally established. Apply analytical evaluation methods and calculations involving triangulation, compound angles, etc., as necessary throughout the inspection cycle. Serialize and maintain a log for parts, assemblies, tooling, etc.
3. Perform mechanical and electrical functional acceptance tests on purchased and manufactured parts and material such as Brinell & Rockwell hardness, non-destructive, spring, etc Review and verify that incoming purchase orders, parts, materials and related documentation received are in compliance with established specifications and standards.
4. Verify that inspection instruments such as micrometers, fixture gauges and thread gauges, etc., are within the designated calibration period prior to use.
5. Perform similar or lower classified work as required.
SCOPE, PURPOSE AND FREQUENCY OF CONTACTS:
Manufacturing To inspect and evaluate material and clarify standards - Frequent
Engineering To clarify standards or to evaluate questionable material - Occasional
Resident Government/Inspectors To discuss defective parts/materials and clarify standards - Frequent
Customer Representatives/
Underwriter Inspectors
Purchasing/Vendors To discuss defective materials - Frequent
DIRECTION OF OTHERS:
Advise shop personnel in proper procedures with regard to quality problems. Provide guidance to lower classified inspectors.
DIRECTION RECEIVED:
Receives work assignments from supervisor and accomplishes work assignments essentially on own initiative. May receive assistance and guidance from higher classified inspectors.
EDUCATION REQUIREMENT:
High school graduate and courses in Engineering Drawing, Metrology, Physics and Mathematics through Trigonometry or the equivalent.
EXPERIENCE REQUIREMENT:
At least two years experience as an Inspector or the equivalent related experience including machining, assembly, nondestructive testing and welding. Prefer familiarity with the division’s products, manufacturing methods and procedures. Must read and understand drawings using the geometric tolerancing and dimensioning system.
This is a Union Represented position.
BASIC QUALIFICATIONS:
High School Diploma or equivalent GED and courses in Engineering Drawing, Metrology, Physics and Mathematics through Trigonometry or the equivalent.
Minimum of 2 years' experience as an Inspector or the equivalent related experience including machining, assembly, nondestructive testing, and welding.
Minimum of 2 years experience with products such as Micrometers, calipers, and optical comparator.
Minimum of 2 years experience with drawings using the geometric tolerancing and dimensioning system.
Minimum of 2 years experience with engineering drawings/blueprints with GD&T (Geometric Dimensioning and Tolerancing).
Minimum of 2 years experience using various handheld (manual and auto) inspection tools/surface plate inspectors.
Experience using SAP, Job Boss, Epicore, or Microsoft access.
US citizenship required.
PREFERRED QUALIFICATIONS:
Experience with CMM setup and/or Faro or Romer arm setup and operation using PC-DIMS.
Experience verifying chemical and mechanical properties of the materials heat report.
#MPR
The application period for the job is estimated to be 20 days from the job posting date. However, this timeline may be shortened or extended depending on business needs and the availability of qualified candidates.Northrop Grumman is an Equal Opportunity Employer, making decisions without regard to race, color, religion, creed, sex, sexual orientation, gender identity, marital status, national origin, age, veteran status, disability, or any other protected class. For our complete EEO and pay transparency statement, please visit http://www.northropgrumman.com/EEO. U.S. Citizenship is required for all positions with a government clearance and certain other restricted positions.